Heat TreatmentMetal Additive ManufacturingPost-Processing

Titomic applies Hot Isostatic Pressing at ANSTO

Australia's Nuclear Science and Technology Organisation acquired the HIP technology to improve the material performance of the titanium components it produces

Stay up to date with everything that is happening in the wonderful world of AM via our LinkedIn community.

Titomic, the advanced manufacturing company, is applying Hot Isostatic Pressing (HIPing) at Australia’s Nuclear Science and Technology Organisation (ANSTO) to improve the material performance of the titanium components it produces. ANSTO acquired the HIP technology to support ANSTO Synroc, an innovative waste treatment process.

“ANSTO has over 30 years of operating expertise in HIP and manages Australia’s largest HIPing facilities. Our capability, which includes qualifying and characterizing the performance of materials before and after the thermal treatment process, is a very useful capability for those in the manufacturing industry,” said Gerry Triani, Technical Director at ANSTO Synroc Technologies.

Titomic uses commercially pure titanium as a powdered raw stock, as opposed to titanium alloy powder, in the additive manufacturing of net shape products for extreme environments, such as aerospace components.

Hot Isostatic Pressing is a manufacturing process used to improve the properties of a material by reducing porosity and refining the microstructure. It involves exerting inert gas pressure on the material at elevated temperatures to eliminate the closed porosity of manufactured components.

Titanium has a high strength-to-weight ratio, good mechanical properties, and excellent corrosion resistance but is difficult to process into engineered materials. The raw material is considerably less expensive than titanium-aluminium alloy powders which are produced by atomising bulk material – typically spherical.

“Titanium is a very sensitive material, probably one of the worst in terms of being affected by other elements, it is particularly sensitive to the effects of oxygen,” said former aerospace engineer, Neil Matthews AM, who is now a Senior Technical Fellow at Titomic. “We have been investigating the use of post-processing and HIPing to reduce porosity in the titanium part to less than one percent, which is comparable to the standard for conventionally produced titanium aluminum alloys.”

Titomic applies Hot Isostatic Pressing (HIP) at ANSTO to improve the material performance of titanium components.
Cold sprayed titanium sample before HIPing (left), and after HIPing (right).

The main issue is the formation of pores/voids generated as part of the layered deposition build-up. When under high loads, these voids compromise ductility – the ability to stretch or bend – which in turn leads to catastrophic fracture modes. The presence of voids can also impact the durability of parts under cyclic loading. “We look at the optimization of all parameters, particle size, particle velocity, and subsequent mechanical behavior during additive manufacturing,” said Matthews.

He also said that using particles with an irregular shape, rather than spherical, in the cold spray, was found to improve the speed of the build and reduce voids. Therefore, porosity had to be addressed for the conditions in which these materials operate. The presence of voids increases the likelihood of multiple crack initiations, which can join up to make a part brittle  – compromising structural integrity.

“A titanium part or repair we supply has to perform at the same level as a part produced by the conventional thermal process of metal production,” he added. “Our goal is to produce a material with good mechanical properties, very close to what the highest ranked titanium alloys, such as Ti64, provide as the standard.”

“Following the optimization of the cold spray additive manufacturing process to provide maximum deposition efficiency and maximum bond strength at Titomic, we apply heat treatment to realign the grains and improve microstructure and then HIPing to increase density as post-processing steps,” said Matthews. The HIPing at ANSTO involved applying a maximum pressure of 200MPa in an argon atmosphere to the material.

Matthews, who has expertise in the acceptance and certifications relating to AM processes, said that an understanding of the science behind the post-processing methods was important to industry regulators and customers. “We need specialists, such as ANSTO material scientists, to choose parameters, including temperature and pressure and isothermal hold time for the HIPing.”

The problem of pore generation and induced stresses in AM applies to other technologies in this sector, too.

Research
Composites AM 2024

746 composites AM companies individually surveyed and studied. Core composites AM market generated over $785 million in 2023. Market expected to grow to $7.8 billion by 2033 at 25.8% CAGR. This new...

Edward Wakefield

Edward is a freelance writer and additive manufacturing enthusiast looking to make AM more accessible and understandable.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close Popup
Privacy Settings saved!
Privacy Settings

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

These cookies are necessary for the website to function and cannot be switched off in our systems.

Technical Cookies
In order to use this website we use the following technically required cookies
  • PHPSESSID
  • wordpress_test_cookie
  • wordpress_logged_in_
  • wordpress_sec

Decline all Services
Save
Accept all Services

Newsletter

Join our 12,000+ Professional community and get weekly AM industry insights straight to your inbox. Our editor-curated newsletter equips executives, engineers, and end-users with crucial updates, helping you stay ahead.