Additive ManufacturingAdditive Mass Production - AMPMetals

GE Additive Avio Aero to install several new Spectra H metal 3D printers

Targets production of up to 60 thousand turbine blades yearly by 2023

Stay up to date with everything that is happening in the wonderful world of AM via our LinkedIn community.

First 3D printing was for single parts, then it became for short batches of 10, 100, 500 and thousands of parts. With the arrival of HP and planar technologies, we’ve started to refer to as short batches production runs of several thousand and even a million pieces. Now GE Additive is using its pioneering Avio Aero plant in Cameri to go into some serious part production capabilities using mainly EBM technology and the new Spectra H systems.

Cameri gets bigger

The next generation of additive machines are already installed at the factory of the future in Cameri, to 3D print turbine blades for the new GE9X engine and to continue expansion.

David Joyce, Vice Chairman of GE and President and CEO of GE Aviation recently stated that “Additive manufacturing is the Netflix of manufacturing”. And it might have been the Avio Aero plant in Cameri,  that inspired his choice of words. That is because, Cameri has been making a name for itself recently, following an expansion plan that has increased its production capacity like never before.

The plan has been accompanied – in lockstep – by Arcam EBM, a division of  GE Additive whose electron beam machines having been manufacturing airplane engine parts at the Novara plant since it was established in 2013.  A few weeks ago the production area was increased by 600 sqm, and the plant currently hosts some 35 Arcam machines.

GE Additive Avio Aero Spectra H

Of these, there are  31  Arcam A2X machines. The other 4 machines are the new Arcam EBM Spectra H. There will be at least another 16 Spectra H machines and in the short run before the Cameri plant is expected to undergo another major expansion run. Eventually, the entire machine fleet will be replaced by the new models.

Targeting 60,000 parts

The A2X machines heat and melt layer by layer metal powder together, producing TiAl (titanium aluminum) blades for assembly on the low-pressure turbine of the new large GE9X engine, which flew for the first time one year ago. Everything starts with the technical drawing of the blades, and once it is sent to the A2X machine, it produces 6 blades per batch in about three days. Arcam’s new Spectra H machine can produce up to 10, in around the same time.

“Thanks to the expansion and these new machines, with greater mechanical and electronic stability, we will definitely be able to produce a larger number of blades”


Additively manufactured TiAl blades are half the weight of traditional nickel alloy turbine blades. For the GE9X engine, this means a fuel consumption reduction of 10% (and therefore emissions), compared to its predecessor, the GE90. The GE9X, which boasts about 200 kg less weight, is expected to enter service in 2020. And, it is estimated that about 60 thousand blades will be produced between 2022 and 2023. The new parts will have greater mechanical and electronic stability, integrating new geometries.

Arcam has followed the evolution and growth of the technology and capacity of the Novara plant since the very beginning.  In 2011 there were only six machines in Cameri. Today there are more than 30 machines there and that the number of Spectra H machines will increase. There is no doubt that we are truly witnessing a momentous paradigm shift. Indeed, from the beginning of April this year, and for the very first time since its opening, continuous production cycles will begin in Cameri.

Composites AM 2024

746 composites AM companies individually surveyed and studied. Core composites AM market generated over $785 million in 2023. Market expected to grow to $7.8 billion by 2033 at 25.8% CAGR. This new...

Davide Sher

Since 2002, Davide has built up extensive experience as a technology journalist, market analyst and consultant for the additive manufacturing industry. Born in Milan, Italy, he spent 12 years in the United States, where he completed his studies at SUNY USB. As a journalist covering the tech and videogame industry for over 10 years, he began covering the AM industry in 2013, first as an international journalist and subsequently as a market analyst, focusing on the additive manufacturing industry and relative vertical markets. In 2016 he co-founded London-based VoxelMatters. Today the company publishes the leading news and insights websites and, as well as VoxelMatters Directory, the largest global directory of companies in the additive manufacturing industry.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close Popup
Privacy Settings saved!
Privacy Settings

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

These cookies are necessary for the website to function and cannot be switched off in our systems.

Technical Cookies
In order to use this website we use the following technically required cookies
  • wordpress_test_cookie
  • wordpress_logged_in_
  • wordpress_sec

Decline all Services
Accept all Services


Join our 12,000+ Professional community and get weekly AM industry insights straight to your inbox. Our editor-curated newsletter equips executives, engineers, and end-users with crucial updates, helping you stay ahead.