AM ResearchMaterialsMetals

Fatigue-resistant 3D printed aluminum alloy created by CityU

Applications could extend to other 3D printed alloys and pave the way for lightweight, load-efficient components across various industries

Stay up to date with everything that is happening in the wonderful world of AM via our LinkedIn community.

According to the City University of Hong Kong (CityU), over 80% of engineering failures stem from material fatigue, a critical aspect in designing lightweight structures in mechanical systems like aircraft, automobiles, and energy-production setups. A joint venture between CityU and Shanghai Jiao Tong University has led to a breakthrough with the creation of an aluminum alloy boasting remarkable fatigue resistance through advanced 3D printing techniques. This new strategy – enhancing fatigue resistance – extends to other 3D printed alloys and paves the way for lightweight, load-efficient components across various industries.

“The fatigue phenomenon in metals was discovered about two centuries ago. Since then, fatigue failure has become one of the most important issues in the lifespan and reliability of all dynamic mechanical systems, such as those in aircraft, automobiles, and nuclear power plants,” said Professor Lu Jian, Dean of the College of Engineering, and Director of the Hong Kong Branch of the National Precious Metals Material Engineering Research Center (NPMM) in CityU, who co-led the research.

Conventional metals exhibit fatigue strength generally lower than half their tensile strength. “Low fatigue strength is caused mainly by multi-scale defects in the materials, which continue to grow and evolve with cyclic loading, forming macroscopic cracks and expanding eventually into larger cracks that destroy the entire material structure,” he explained. “This challenging phenomenon also happens in alloys produced by additive manufacturing, also known as 3D printing, limiting further applications of 3D printed materials.”

To overcome the issue of low fatigue resistance in 3D printed alloys and generally in all metal materials, a joint-research team of CityU and Shanghai Jiao Tong University used Laser Powder Bed Fusion (LPBF) to successfully fabricate a novel aluminum alloy from AlSi10Mg powders decorated with TiB2 nanoparticles. The fatigue resistance of this 3D printed nano-TiB2-decorated AlSi10Mg (NTD-Al alloy) is more than double that of other 3D printed aluminium alloys and surpassed those of high-strength wrought AI alloys.

The findings were published in Nature Materials under the title “Achieving ultrahigh fatigue resistance in AlSi10Mg alloy by additive manufacturing”. They were also featured in the ‘Research Highlights’ of the prestigious scientific journal Science, which described it as a general strategy for other alloys to boost fatigue resistance.

The team used micro-computed tomography to investigate this 3D printed NTD-Al alloy and found throughout the sample a typical continuous 3D-dual-phase cellular nanostructure, which consisted of a network of solidification cellular structure with an average diameter of about 500 nanometers. The 3D-dual-phase cellular nanostructure acts as a strong volumetric nanocage to prevent localized damaged accumulation, inhibiting fatigue crack initiation.

Fatigue-resistant 3D printed aluminum alloy created by CityU. Applications could extend to other 3D printed alloys.
Microstructure of the AM NTD-Al alloy. (A) μ-CT analysis showing the spatial and size distribution of printing defects; the largest defect was 73 µm, only about 1/3 of the size of defects in AM AlSi10Mg alloy without TiB2 decoration. (B) Grain morphology of the printed sample. (C) A network of solidification cellular structures with an average diameter of ~ 500 nm. (D) Continuous 3D Si cellular structure revealed by BSE/FIB tomography. (E) Cellular structure consisting of nanosized Si phases revealed by TEM. Photo credit: Dan, C. et al.

“The three-dimensional network of nano eutectic silicon (Si) generated by additive manufacturing inside the alloy due to rapid solidification could block the movement of dislocations, thus suppressing fatigue crack initiation,” said Professor Lu. “With controlled defects through process optimization, the fatigue limit of the bulk NTD-Al alloy is superior to that of all existing Al alloys.”

In a series of fatigue tests, the research team found that the printed bulk NTD-Al alloy achieved fatigue resistance of 260 MPa, which was more than double that of other additive manufacturing Al alloys. The high fatigue strength limit of the bulk NTD-Al alloy surpassed that of all other Al alloys, including conventional high-strength wrought Al alloys with limited metallurgical defects.

The NTD-Al alloy has already been applied to fabricate prototypes of large thin-walled structures, including the fan blades of aircraft engines designed for high fatigue strength, and successfully passed the qualifying fatigue test.

“These findings indicate the potential applicability of our alloy for the lightweight structures necessary in industries where fatigue properties are the key design criterion. Our alloy can help reduce weight by increasing the load efficiency of moving components,” added Professor Lu.

Combined with the advantages of 3D printing, the latest discovery will boost lightweight design and reduce carbon emissions in modern industries. And the same strategy can be also used for other materials to help solve the fatigue failure challenge in metal additive manufacturing,” concluded Professor Lu Jian.

The study was a collaboration between Professor Wang Haowei’s and Professor Lu’s teams. The co-first authors of the paper are Dr Dan Chengyi, Assistant Professor Cui Yuchi, Associate Professor Wu Yi, and Professor Chen Zhe from Shanghai Jiao Tong University. The co-corresponding authors are Professor Lu from CityU and Professor Chen. Also participating in the study was Dr Liu Hui, a former postdoc in the Department of Mechanical Engineering at CityU.

This research was supported by the National Natural Science Foundation of China, the Conseil Regional du Nord-Pas de Calais, and the European Regional Development Fund.

Research
Composites AM 2024

746 composites AM companies individually surveyed and studied. Core composites AM market generated over $785 million in 2023. Market expected to grow to $7.8 billion by 2033 at 25.8% CAGR. This new...

Edward Wakefield

Edward is a freelance writer and additive manufacturing enthusiast looking to make AM more accessible and understandable.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close Popup
Privacy Settings saved!
Privacy Settings

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

These cookies are necessary for the website to function and cannot be switched off in our systems.

Technical Cookies
In order to use this website we use the following technically required cookies
  • PHPSESSID
  • wordpress_test_cookie
  • wordpress_logged_in_
  • wordpress_sec

Decline all Services
Save
Accept all Services

Newsletter

Join our 12,000+ Professional community and get weekly AM industry insights straight to your inbox. Our editor-curated newsletter equips executives, engineers, and end-users with crucial updates, helping you stay ahead.