Automotive AMCase StudiesMaterialsMotorcycles

Windform GF materials used to solve wiring issues in motorsports

Stay up to date with everything that is happening in the wonderful world of AM via our LinkedIn community.

Wiring in race cars is becoming more and more complex. Power Units are made up of several parts that need to be integrated into the final assembly. Available space is increasingly limited, so engineers are frequently utilizing flexible parts such as cooling ducts and wiring harnesses. A new innovative SLS (Selective Laser Sintering) Front Air Inlet made with WINDFORM GF high-performance materials can provide a viable solution to these issues.

CRP Technology’s R&D department tackled the development of a new front air inlet for a Moto3 racing customer to solve space issues in the front fork area. It was manufactured in WINDFORM materials using SLS technology.

Testing had shown that increasing air flow to the air-box improved the performance of the engine at every RPM range. This led the team as well as the engineers to conclude that they need to design a new track-ready inlet. This design would make the air inlet longer, and bring the opening up to the front side of the fairing, in order to have a direct airflow with less turbulence.

Among the goals to be achieved, was the need to avoid modifying the existing frame and the existing triple clamps. The design would have to fit to the existing platform in order to test the on-track advantages and disadvantages of using this solution and to make a direct comparison with the current standard inlet.

The WINDFORM materials allowed for total freedom and no limitations in design (Design For Functionality instead of Design for Manufacturing). They enabled the creation of mock-up for assembling, fitting, and functionality, as well as the production of parts for performance tests. This resulted in a reduction in product and project realization time requirements.

The final decision to use the new inlet came from its behavior on track with the key points being its performance and reliability. Engineers kept the current airbox with the aim to mount the traditional air inlet as well as the new one and to acquire data of the airbox pressure on the track.

Windform GF materials used to solve wiring Issues in motorsports case study

The WINDFORM GF roject

Through the use of Reverse Engineering, the original airbox was scanned and virtually assembled with the CAD system. This allowed the engineers to be able to create a new model of the air inlet by taking into account the amount of available space, and the constraints of the assembly of the current airbox and frame.

Once a first draft of the air inlet was developed, a prototype in WINDFORM GF 2.0 was created. The decision to use WINDFORM® GF 2.0 was made to reduce costs while being able to perform multiple tests with multiple prototypes.

The first prototype allowed engineers to see if the design fitment was correct and suitable for assembly. It was revealed by the first design that some sections needed to be changed due to the lack of space available under the lower triple clamp. This problem is further complicated when the bike is cornering and under braking conditions.

To optimize the volume of the inlet duct under the lower triple clamp, the engineers adopted a creative approach and decided to use a portion of the duct in WINDFORM® RL, the new rubber-like composite material produced by CRP Technology. This would be bonded to the main structure that was made out of WINDFORM® XT 2.0 for evaluation in racing conditions. To facilitate this they also carried out a bonding test to study the characteristics of the final assembly.

The concept was to make the bottom part of the duct with WINDFORM® RL in the fork and triple clamp area and then assemble this into the top part produced in WINDFORM® XT 2.0. This approach would allow good clear airflow on the straightaway sections of the course, and thus an excellent flow to the airbox. Under braking, the front fender could move up and collapse the inlet duct without any damages, due to the flexible material.

In addition, it was decided after examining the part that making the ducting flexible in the same area next to the front forks would off an additional benefit. The engineers were able to maximize the duct volume because the maximum steering actions are only reached when the bike is pushed into the paddock by the technical staff. In this situation, the front fork can tough the inlet duct deforming it without any damages.

Second prototype

A second prototype was made in WINDFORM® GF 2.0. Comparison between the two prototypes. First prototype: outlined in yellow changes to be made. Second prototype: the flexible area has been redesigned (outlined in red) in order to ensure the mobility of the steering. Once the second prototype was mounded the engineers noticed some changes to be made, especially in the front fork area.

The soft section was too short and the forks could touch the area of the duct near the bonding overlap when steering travel was checked from lock to lock position. It was also seen that toward the back of the flexible area, near the airbox, that the duct was very close to the front wheel in the maximum braking position.

During testing, it was determined that when the motorcycle was under severe braking, the front fender contact area on the duct in the soft part was too large. This situation, from the rider’s point of view, was not good because, during hard braking, the steering must be free from movements, as the rider might need to correct the trajectory quickly.

The amount of input from the rider may be small, but it must occur very smoothly and too much contact of the front wheel assembly gave the impression of drag on steering. This affected the way the rider felt on the bike.

The team and engineers decided to change the inlet by reducing the portion that would make contact with the fender to reduce drag perceived by the rider. The part made in WINDFORM® RL was enlarged according to the second test, and engineers and the rest of the team could get the correct fit for performance.

In the final test version, WINDFORM XT 2.0 was utilized in order to reduce the weight of the front and central part of the inlet, while the WINDFORM RL material was used for the flexible part of the inlet. The two parts were bonded together after being produced.

Bonding SLS parts is very important for the final result of the prototype: the right selection of bonding methods and adhesives will influence accuracy and functionality.


Composites AM 2024

746 composites AM companies individually surveyed and studied. Core composites AM market generated over $785 million in 2023. Market expected to grow to $7.8 billion by 2033 at 25.8% CAGR. This new...


VoxelMatters is the online trade media portal published by 3dpbm, a leading marketing and market research firm specializing in the AM industry. 3dpbm also publishes the 3D Printing Business Directory, the AM Focus eBook series and the 3dpbm Research AM Market Reports. 3D Printing Media Network was founded with the goal to provide the latest industry news, insights and opinions to a global audience of professionals and decision makers.

Related Articles

Back to top button
Close Popup
Privacy Settings saved!
Privacy Settings

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

These cookies are necessary for the website to function and cannot be switched off in our systems.

Technical Cookies
In order to use this website we use the following technically required cookies
  • wordpress_test_cookie
  • wordpress_logged_in_
  • wordpress_sec

Decline all Services
Accept all Services


Join our 12,000+ Professional community and get weekly AM industry insights straight to your inbox. Our editor-curated newsletter equips executives, engineers, and end-users with crucial updates, helping you stay ahead.