Ceramic Additive ManufacturingMass Customization

VormVrij and Unfold Studio Collaborate on Mass Production of 1200 3D Printed Clay Cups

Stay up to date with everything that is happening in the wonderful world of AM via our LinkedIn community.

In Fall 2017 Studio Unfold contacted VormVrij 3d for a commission that would put their 3D clay printers to the ultimate test. 400 identical 3D printed clay cups, glazed and packed for shipment within 14 days. If they could pull it off two more batches would follow the next 4 weeks making a total production of 1200 cups in 6 weeks. The challenge was accepted, the correct clay was ordered, and preparations started.

“For mass production we had to optimize printing. The design of this particular cup is somewhat crenelated with sharp corners. This would not allow for maximum print speeds as the directional shifts at those points could vibrate the printed object when printing at high velocity,” said Yao vd Heerik, CEO and head developer at VormVrij3D.

3d printed clay cups

Another interesting addition to the code was a small warning signal just before a cup was about to finish. This would give Yao the option to check upon progress before the next cup would start to print leaving time to do other tasks while the printers were busy.

“The standard slicing resulted in print times that would far exceed the time we had. Optimization was key and after making several tweaks, like variable print speeds throughout the cups to optimize surface quality while maintaining minimal vibration, printing each of 5 close to one another and dynamic acceleration and deceleration at the start and end of a cup we brought print times down to acceptable levels. All this was done directly in the original Gcode of a single cup as those particular variables could not be produced with the slicing software,” Yao explained.

3d printed clay cups

With an average layer height of 1mm, a wall thickness stable at 3mm and printing at speeds between 10 and 40mm per second a full row of five would print in just over an hour. The plaster slabs were cut to fit this purpose. As the Print bed of a LUTUM printer is stationary you can easily place multiple objects side by side in one print leaving minimal downtime in the overall process. When the plaster slab is full, Swapping the slab and the cartridge takes less than a minute. To increase production volume they used 4 printers simultaneously.

November was a cold month and VormVrij’s new studio was cooler than anticipated. As a result, they had to speed up the drying process keeping their kilns permanently warm. Post-processing like sponging and glazing took about the same level of overtime. Night work was no exception that November.

“It’s always exciting to open a glaze fire and with much relief and fulfillment the first batch came out perfectly.”

After wrapping and packing the 3D printed clay cups they were collected by Dries and Claire from Unfold. They would repackage and distribute the prints to their future owners, but that is a different story.

3d printed clay cups

The next 800 3d printed clay cups were just as much work but Yao and Marlieke now knew it could be done. It turned out the commission was less of a challenge for the printers as they performed exactly according to expectations. A few hickups like a worn seal and some unwelcome particles in the clay were to be expected.

In the end, the drying time, post-processing handwork, glazing plus firing and cooling times were the biggest factors to take into account. Rigid planning was necessary to make sure one step wouldn’t delay the next. And this is the result:

Composites AM 2024

746 composites AM companies individually surveyed and studied. Core composites AM market generated over $785 million in 2023. Market expected to grow to $7.8 billion by 2033 at 25.8% CAGR. This new...


VoxelMatters is the online trade media portal published by 3dpbm, a leading marketing and market research firm specializing in the AM industry. 3dpbm also publishes the 3D Printing Business Directory, the AM Focus eBook series and the 3dpbm Research AM Market Reports. 3D Printing Media Network was founded with the goal to provide the latest industry news, insights and opinions to a global audience of professionals and decision makers.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close Popup
Privacy Settings saved!
Privacy Settings

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

These cookies are necessary for the website to function and cannot be switched off in our systems.

Technical Cookies
In order to use this website we use the following technically required cookies
  • wordpress_test_cookie
  • wordpress_logged_in_
  • wordpress_sec

Decline all Services
Accept all Services


Join our 12,000+ Professional community and get weekly AM industry insights straight to your inbox. Our editor-curated newsletter equips executives, engineers, and end-users with crucial updates, helping you stay ahead.